Minelab F3 Specifikace Strana 1

F3 COMPACTRevision 02 Part No: 4901-0103OPERATIONS MANUAL

8F3 COMPACT Operations Manual2.3 F3 COMPACT PreparationTo prepare the detector for use, conduct the following procedure:a. Open the Hard Case and/or

F3 COMPACT Operations Manual91 23 45

10F3 COMPACT Operations ManualAB67 8Figure 5: Guide to unfolding and adjusting the F3 COMPACTNOTEWhen the Handle Assembly is locked into position (Fra

F3 COMPACT Operations Manual11Figure 6: F3 COMPACT in the standing, kneeling or prone positionsg. Undo the dust caps from the Earset plug and Earset

12F3 COMPACT Operations ManualNOTEThe Earset connector is waterproof and must be connected and disconnected from the Earset socket by holding the rubb

F3 COMPACT Operations Manual133. Functional Description3.1 Functional Controls and DisplaysFor ease of use, all controls and displays for the F3 COM

14F3 COMPACT Operations ManualOn completion of the Start-Up Tones the F3 COMPACT emits a low steady tone known as the Threshold Tone, which confirms t

F3 COMPACT Operations Manual15* WARNING *When detecting minimum metal mines or targets with low metal signatures, the F3 COMPACT should not be used on

16F3 COMPACT Operations Manual3.1.5 LED DisplayA display of nine red LEDs provides a visual indication of target size and proximity. The display can

F3 COMPACT Operations Manual17NOTEThe LED display will always be off when the detector is first switched on.3.1.6 Battery StatusProvided that the LED

WARNINGTHIS DOCUMENT CONTAINS INTELLECTUAL PROPERTY, TECHNICAL AND PROPRIETARY DATA AND INFORMATION AND OTHER MATERIAL OWNED SOLELY BY MINELAB ELECTRO

18F3 COMPACT Operations Manual3.2 Functional TonesThe F3 COMPACT emits tones that vary in pitch and volume to alert the operator to targets, automati

F3 COMPACT Operations Manual19Tones Event DescriptionDefault Sensitivity Not Selected Indicates that the default sensitivity is not selected when dete

20F3 COMPACT Operations ManualNOTEWhen switched on, maximum sensitivity is available 30 seconds after the Threshold Tone commences. Do not test the de

F3 COMPACT Operations Manual214. Operating Procedures4.1 IntroductionThe F3 COMPACT is designed to ensure that operation of the detector is as simpl

22F3 COMPACT Operations Manual4.2 Standard ProcedureFigure 13: F3 COMPACT controlsAfter unpacking the F3 COMPACT and preparing it for use as describe

F3 COMPACT Operations Manual23b. If the Threshold Tone is steady continue with STEP 2. If the Threshold Tone is noisy or uneven when the coil is stat

24F3 COMPACT Operations ManualIf the Ground Balance OK tone is not heard within 20 seconds of starting the procedure, release the Ground Balance butto

F3 COMPACT Operations Manual25NOTEMaximum sensitivity is only available 30 seconds after the Threshold Tone commences. Do not test the detector with t

26F3 COMPACT Operations Manual4.3 Optional ProceduresIf after Step ONE the Threshold Tone is not low and steady, conduct one or both of the following

F3 COMPACT Operations Manual27NOTEThe detector cannot be used for clearing operations during Noise Cancel. The coil should not be moved during this pr

F3 COMPACT Operations Manual1Table of Contents1. Introduction ...3

28F3 COMPACT Operations ManualFigure 19: Standard and optional proceduresSTEP 1SWITCH ONSTEP 2GROUND BALANCESTEP 3TEST PIECENOISECANCELAUDIORESETThres

F3 COMPACT Operations Manual29Noise Cancel and Audio Reset procedures can be performed any time the Threshold Tone becomes noisy, uneven or rises in v

30F3 COMPACT Operations ManualDepth of detection depends on target distance from the coil, not depth of the target under the ground. Therefore, the co

F3 COMPACT Operations Manual31At the change of the Threshold Tone, the operator should mentally mark the position on the ground, move the coil away, a

32F3 COMPACT Operations Manual4.5.2 STEP 2 Determine Centre of TargetIn Step 1, the area of a target was determined. If the metal in the target is su

F3 COMPACT Operations Manual334.6 Multiple TargetsThere may be occasions when an operator will encounter multiple targets. For example, small anti-pe

34F3 COMPACT Operations Manual4.6.2 STEP 2 Determining the Centre of TargetThe pitch of the Threshold Tone will rise or fall depending on the combin

F3 COMPACT Operations Manual35b. Once Noise Cancel is finished on the first detector, leave it switched on. Ensure that the second detector is at lea

36F3 COMPACT Operations Manuald. Disconnect the Earset.e. Retract the Middle and Lower Shafts rotating the coil to the stowed position.f. Collapse

F3 COMPACT Operations Manual375. Care and Troubleshooting5.1 Routine CareThe F3 COMPACT is designed for lasting use in harsh operating environments,

2F3 COMPACT Operations Manual4.5 Pinpointing Procedure 304.5.1 STEP 1 Mapping the Target ...304.5.2 STEP 2

38F3 COMPACT Operations Manual5.2 TroubleshootingTable 2 provides several troubleshooting procedures in response to a variety of possible problems.Pr

F3 COMPACT Operations Manual396. SpecificationsLengthOperating Length 1490 mm/59 ins – 950 mm/37 insWeightOperating weight with batteries (complete)2

40F3 COMPACT Operations ManualBatteriesAlkaline 4 x C cell LR14Rechargeable 4 x NiCad or NiMh C cell minimum 4000 mAh capacityBattery Reverse Polarity

Contact Details:Minelab Electronics Pty Ltd tel: +61 8 8238 0888Minelab Americas Inc tel: +1 630 401 8150Minelab International Limited tel: +353 21 42

F3 COMPACT Operations Manual31. IntroductionSince 1996, Minelab has designed, developed and manufactured its range of detectors to meet the requireme

4F3 COMPACT Operations ManualThe F3 COMPACT is a robust detector that is extremely simple to operate. When working in an environment that includes hig

F3 COMPACT Operations Manual52. General Description and Preparation2.1 Mine Detecting SetThe F3 COMPACT is supplied as a mine detecting set (Figure

6F3 COMPACT Operations Manual2.2 F3 COMPACT Main ComponentsFigure 3 identifies the main components of the F3 COMPACT.BatteryCompartmentArmrestArmrest

F3 COMPACT Operations Manual7Test Piece – conveniently stowed on the Armrest to allow the operator to ensure the detector is working at its operationa